Page 1 of 1
QL hulp met .223 asb
Posted: Tue Jul 04, 2023 5:42 pm
by Jacques.308
Hi manne kan iemand my dalk met QL help asb.
Tikka T3 Varmint
Loop lengte =23.7 duim
Twist = 8 duim
H20 volume = 31 gr
Punte = 75gr ELD-M
Kruit = Varget 25,1 gr
Gem spoed = 2996 FPS
Totale patroon lengte =62,5mm
Sent from my SM-S901E using Tapatalk
Re: QL hulp met .223 asb
Posted: Tue Jul 04, 2023 5:55 pm
by Dale SH
Your burn rate is unrealistically high.
This load is already predicted to be running at 63325 psi
What is your jump to the lands and what instrument did you measure the velocity with ?
Re: QL hulp met .223 asb
Posted: Tue Jul 04, 2023 6:12 pm
by Jacques.308
Dale SH wrote:Your burn rate is unrealistically high.
This load is already predicted to be running at 63325 psi
What is your jump to the lands and what instrument did you measure the velocity with ?
Hi Dale
Measured with magneto.
Jump is 2 thou of the lands.
Speed at 23 gr and 1mm of the lands is 2722 fps
Sent from my SM-S901E using Tapatalk
Re: QL hulp met .223 asb
Posted: Tue Jul 04, 2023 6:20 pm
by Dale SH
Two thousands of an inch is 0.0508mm,that is as good as being in the lands as far as creating a pressure spike is concerned,
Where do you want to be at with this load ?
In the lands or 1mm away ?
Your answer will determine my calculation.
Re: QL hulp met .223 asb
Posted: Tue Jul 04, 2023 6:26 pm
by Dale SH
Re: QL hulp met .223 asb
Posted: Tue Jul 04, 2023 6:26 pm
by Jacques.308
Sorry dale typo there 6 thou of the lands. Will you maybe do a cal for both.
25,1 gr varget
62,5 mm at 2996 fps
61,8 mm at 2980 fps
Sent from my SM-S901E using Tapatalk
Re: QL hulp met .223 asb
Posted: Tue Jul 04, 2023 6:35 pm
by Dale SH
At 61.8mm COL
24.5 grains
2919 fps
+- 57750 psi ( which is still above SAAMI max for 223 Remington but below 5.56 x 45mm maximum)
At 62.5mm COL
24.35 grains
2920 fps
57820 psi
Re: QL hulp met .223 asb
Posted: Tue Jul 04, 2023 6:37 pm
by Jacques.308
Thanks Dale. I saw the same on my QL. Thats why im asking a second opinion. There are absolutely no visible signs of pressure and no heavy bolt lift.
Sent from my SM-S901E using Tapatalk
Re: QL hulp met .223 asb
Posted: Tue Jul 04, 2023 6:39 pm
by Dale SH
If your cases are head spaced to 2 thou or less you wont see the pressure signs,
Bolt lift should be noticeable from late 60k or early 70k pressures.
Re: QL hulp met .223 asb
Posted: Tue Jul 04, 2023 6:40 pm
by Jacques.308
Shoulders bumped at 1 thou
Sent from my SM-S901E using Tapatalk
Re: QL hulp met .223 asb
Posted: Tue Jul 04, 2023 6:41 pm
by Dale SH
Just remember that some of those bullets may have 6thou or more deviation in their length so you may also be in the lands with some of the bullets.
Re: QL hulp met .223 asb
Posted: Tue Jul 04, 2023 6:42 pm
by Dale SH
Dale SH wrote: Tue Jul 04, 2023 6:41 pm
Just remember that some of those bullets may have 6thou or more deviation in their length so you may also be in the lands with some of the bullets.
Keep an eye on those primer pockets, I suspect you may not get many reloads before the primers are loose.
Re: QL hulp met .223 asb
Posted: Tue Jul 04, 2023 6:43 pm
by Jacques.308
I measure Ogive after determining max total length.
Sent from my SM-S901E using Tapatalk
Re: QL hulp met .223 asb
Posted: Tue Jul 04, 2023 6:46 pm
by Jacques.308
Dale SH wrote:Dale SH wrote: Tue Jul 04, 2023 6:41 pm
Just remember that some of those bullets may have 6thou or more deviation in their length so you may also be in the lands with some of the bullets.
Keep an eye on those primer pockets, I suspect you may not get many reloads before the primers are loose.
Will do so. Need to get a decent grouping first
Sent from my SM-S901E using Tapatalk